3mm Alphabet Plastic Letters and Numbers Includes - Plastic moulded Alphabet and numbers - Ideal for Railway station signage and building names - Requires careful trimming off fret with craft knife - Can be stuck down with suitable plastic glue (poly cement) - N, TT, TT(1:120) and OO Scale
8mm Alphabet Plastic letters and Numbers Includes - Plastic moulded Alphabet and numbers - Ideal for Railway station signage and building names - Requires careful trimming off fret with craft knife - Can be stuck down with suitable plastic glue (poly cement) - N, TT, TT(1:120), OO and O Scale
12-Way Pluggable Connectors (2 pairs)
12-Way Pluggable Connectors (2 pairs) Two pairs of 12 way pluggable connectors, suitable for heavy power connection between baseboards or perhaps the creation of an ‘easy disconnection’ structure between DCC systems and layout, these heavy duty tag strips are able to take a wide range of wires. They are a very strong connector that will last forever! Screws are brass and all pins/sockets are plated solid brass.
15V~4 Amp Transformer (UK) + 15V Power Supply Adapter Bundle
15V~4 Amp Transformer (UK) + 15V Power Supply Adapter Bundle For use with HM7000 APP and HM7000 Decoders
16v AC Cased Transformer - All metal cased transformer for powering Panel mounted controllers - Input Power: 230v Mains - OutPut: 2x 16v AC - Output Rating: 1Amp
21 Pin DCC Loco-Decoder (with Brake Button function)
21 Pin DCC Loco-Decoder (with Brake Button function) A 21 Pin (21MTC) DCC Decoder suitable for models fitted with a 21 Pin DCC decoder socket (do not use with the Bachmann Branchline Class 90 – use 36-569A with these models). This decoder replaces item No. 36-557 and can be used in any model for which item No. 36-557 is recommended Highlights include: Dual-mode DCC/DC decoder with Back EMF function 10 powered function outputs (+8 logic level outputs and 2 logic level/SUSI outputs) 1.5A continuous load RailComPlus® for automatic registration when used with selected DCC systems Suitable for models equipped with DC motors (including coreless motors) Brake Button function for realistic control of braking (operates on F2) Operating Modes: NMRA/DCC with 14, 28 and 128 speed steps Short and Long addresses DCC and DC operation (DC operation is de-selectable) Automatic recognition of operational mode and DCC speed step selection Supports Lenz® LG 100 braking sections Supports ABC braking sections Motor Control Features Suitable for models equipped with DC motors (including coreless motors) 1.5A continuous load Motor regulation with pulse width frequency from 10kHz to 50kHz Motor output overload protection; Back EMF (de-selectable) Function Outputs: 10 powered function outputs with overload protection (4 via 21MTC pins, 6 via solder pads) 10 logic level outputs (8 via 21MTC pins, 2 via solder pads) 250mA load per output 500mA total load of all function outputs 2 additional logic outputs Shunting speed and momentum key selectable Brake Button function for realistic control of braking (operates on F2) Dimensions: 21.4mm x 15.5mm x 4.5mm Default Address: Address 3 Programming: DCC Service Mode & DCC PoM (Programming on Main) Additional Features: RailCom® Feedback system RailComPlus® automatic Registration
4 Pin Decoder
6 Pin 90° DCC Loco-Decoder
6 Pin Micro DCC Loco-Decoder (with Brake Button function)
6 Pin Micro DCC Loco-Decoder (with Brake Button function)
8 Pin Decoder Socket with Harness (x1)
Bachmann 8 Pin Decoder Socket with Harness (x1) Enables locomotives without decoder sockets to have an 8-pin decoder socket fixed to them. Socket Dimensions: 10mm x 10mm x 5mm Cable Length: 90mm cable
Accessory Switch - for fitting to turnout motor PL10
Accessory Switch (mounts on top of PL10 and PL10E Point motors) - Designed to change the polarity of Electrofrog points - OO Gauge
Adaptor Base - Self Assemble No Spring
Adaptor Base for PL10 point motors - Self Assemble No Spring - For use with self latching points - OO Gauge
AE Model 2-Wire High Power Plug & Play Stay-Alive
AE Model 2-Wire High Power Plug & Play Stay-Alive Compatible with Hornby TXS (HM7000) decoders (replaces R7377 / HM7070) to give improved performance and connectivity. AE Model 2-Wire Stay Alive for connection to AE Model Decoders including plug-and-play connector. Dimensions 23mm x 17mm x 6mm Cable length = 120mm
AE Model 2-Wire High Power Plug & Play Stay-Alive (3-Pack)
AE Model 2-Wire High Power Plug & Play Stay-Alive (3-Pack) Compatible with Hornby TXS (HM7000) decoders (replaces R7377 / HM7070) to give improved performance and connectivity. AE Model 2-Wire Stay Alive for connection to AE Model Decoders including plug-and-play connector. Dimensions (individual) 23mm x 17mm x 6mm Cable length = 120mm
AED-6PD.2 6-PIN Direct Function Decoder
AED-6PD.2 6-PIN Direct Function Decoder - 2 Function Decoder
Black Wire (7 x 0.2mm) 100m This wire can be used for point motors, switches, track wiring and many other applications.
Black Wire (7 x 0.2mm) 10m
Blue Wire (7 x 0.2mm) 10m
Cable Clips - self adhesive - Help tidy and neaten wiring under your railway
Capacitor Discharge Unit This device is for operating electrical point Solenoid motors and accessories - Requires wiring to a 16- 24v AC Supply in order to use. - Suitable for N, OO Gauge and O Gauge accessories
Capacitor Discharge Unit (CDU)
Capacitor Discharge Unit (CDU) - This device is for use with Solenoid Point motors (PL10 / PL10E/ PL11) - The CDU is designed to store and release electrical power. When you switch your point blades (via switch like PL26 R/B/W/Y), the extra power ensures the blades throw properly every time. - The CDU requires a 16V Accessory out put either from your controller or via a separate accessory transformer (recommend Gaugemaster GMC WM1 Wall mounted transformer)
Class 90 DCC Loco-Decoder w/Servo Motor Operation & Brake
A 21 Pin (21MTC) DCC Decoder configured for use in the Bachmann Branchline Class 90 – models produced from 2021 onwards. Configured to control the servo-motor-operated Pantograph. Highlights include: Dual-mode DCC/DC decoder with Back EMF function 1.2A continuous load Brake Button function for realistic control of braking Controls the servo-motor-operated Pantograph Default Functions when fitted to Bachmann Branchline Class 90 F0 - Direction Lights on/off F1 - Cab Lights (Directional) on/off F2 - Brake Button F3 - Day/Night Mode F4 - Direction Lights Off (Non-Pantograph End) F5 - Direction Lights Off (Pantograph End) F6 - Pantograph Up/Down
Cobalt Barrel-Plug Adapter (3 Pack)
Cobalt Barrel-Plug Adapter (3 Pack) Includes: A pack of three coaxial DC barrel plug adapters that will let you connect bare wires to a DC-plug fitted power supply that takes away the need to cut the plug off and get the soldering iron out. Suitable for the following DCCconcepts power supplies: - DCP-PS12 - DCP-12.3.XX - DCP-18.2.XX - DCP-18.5.XX
Cobalt iP Digital Point Motor (Single)
Cobalt iP Digital Point Motor (Single) - Any Scale Includes: - 1x Digital Point motor - Instruction manual - Product Size: - Width 28.5mm (67mm over the mounting wings) - Depth 40mm (48mm over the mounting wings) - Height 44mm (67mm over the connector) - Bag of attachments Features: The Cobalt-iP Digital’s super-low static current draw means very low power bus loading and the Cobalt-iP Digital is also able to cope with a very wide range of DC or DCC power supply voltages. We prefer 9~12V regulated power for DC, but any DCC voltage from 7 to 23 volts is acceptable. Cobalt-iP Digital is supplied with the throw bar already centred for easy installation. You can activate and de-activate self-centring and even swap the throw direction with a simple software command. This allows easy matching to layout needs, software driven computer displays, track diagrams or computer control. With Cobalt-IP “Intelligent Power” Digital Motors, you also have all the connection versatility you could ever need already built in. Frog power needs only one added wire, and a totally separate SPDT changeover switch can facilitate interlocking, control of signal feather indicators or ground signals, etc. Cobalt iP Digital also features the ability to add panel switches or control via DCC. The connection terminals used for panel switch connection are also able to give direct high/low state computer or DCC system feedback, so one motor really CAN do it all. Add to the above the ability to work with DC and super-simple wiring or DCC operation, or to combine digital and analog control… and Cobalt iP Digital really is the best choice for all layouts, no matter how you choose to power the trains!
Cobalt SS Medium 600mm Extension Leads (3)
Cobalt SS Medium 600mm Extension Leads (3) Includes - Use these cables to control your Cobalt-SS motors in pairs, either both moving in the same direction, or moving opposite each other.
Cobalt SS Medium 600mm Extension Leads (3)
Cobalt SS Medium 600mm Extension Leads (3) Cobalt-SS Universal extension leads. Use these cables to control your Cobalt-SS motors in pairs, either both moving in the same direction, or moving opposite each other
COMBI Single Track Controller with Plug in Transformer
COMBI - Single Track Analogue Controller with Plug in Transformer Ideal for the beginner with a first train set or expanding on a current railway. Includes - Hand held controller - Mains Transformer Technical: - Input: 230v Mains - Controlled Output: 12v DC - Accessory Output: 16v AC - Rating 1.1Amp - Suitable for N, OO, OO9 and (SMALL Dapol Locomotives) O Gauge
Connectors/Shrouds 10 connectors - 5 shrouds
Connectors/Shrouds Includes - 10 Connectors - 5 shrouds Designed to join on the terminals of Point Motors (PL10/ PL10E etc) to eliminate soldering
DCC Decoder Convertor 3 Wire to 2 Wire (3)
DCC Decoder Convertor 3 Wire to 2 Wire (3) - Pack of three solenoid decoders. - The SDC is a clever wee device that takes the outputs from a 3-wire accessory decoder and turns them into a 2-wire reversing DC decoder, allowing you to use most solenoid accessory decoders to power Kato, Cobalt or other brands of point motor. - Please note that for motor drive decoders you will also need to set ‘power on’ time for between 2 and 4 seconds.
DCD-ZBHP.6 Zen Black Buddha Decoder O & Larger Scale
DCD-ZBHP.6 Zen Black Buddha Decoder O & Larger Scale Includes – 5 Amps peak power– 3 Amps continuous power– 6 functions at 250mA each– On-board high-power stay-alive– 42mm x 27mm x 13mm– 12 screw terminals– One-Step Loco Setup– Shuttle mode (requires ABC boards for this to function)
DCD-ZN68.2 Zen Blue+Decoder NEM651 6-Pin Direct/ Harness 2 Funct
DCD-ZN68.2 Zen Blue+Decoder NEM651 6-Pin Direct/ Harness 2 Funct Includes - 1.1Amps Peak Power - 750mA Continuous power - 2 Functions at 100mA each - Dimensions 13.5mm x 8.5mm - 6 PIN Direct, 6 PIN Harness and 8 PIN Harness - One step loco setup
DCD-ZNM.HP.6 Zen Black Decoder Midi-Sized 8PIN Harness 6 Fct
DCD-ZNM.HP.6 Zen Black Decoder Midi-Sized 8PIN Harness 6 Fct Includes – 3 Amps peak power– 1.5 Amps continuous RMS power– 6 functions (2x 250mA, 4x 100mA)– Size 30mm x 18.3mm x 6mm– 8-pin harness– One-Step Loco Setup– Shuttle mode (requires ABC boards for this to function)– Brown-Out Protection on-board
DCD-ZNmini.4 Zen Black Decoder Mini 8Pin
DCD-ZNmini.4 Zen Black Decoder Mini 8Pin Includes – 1.1 Amps peak power– 750mA continuous power– 4 functions at 100mA each– 19mm x 11mm x 6mm– 8-pin & harness– One-Step Loco Setup– Shuttle mode (requires ABC boards for this to function)– Brown-Out Protection on-board– Stay-Alive connection
DCS-MSET Mega Screw Set 16x 60 Vials (w/20 Drill Bit set)
Mega Screw Set 16x 60 Vials (w/20 Drill Bit set) Mega set of 16 vials each containing 60 panhead (60x 1.0x3mm, 60x 1.0x5mm, 60x 1.0x8mm, 60x 1.5x4mm, 60x 1.5x6mm, 60x 1.5x8mm, 60x 2.0x5mm, & 60x 2.0x8mm) 60 countersunk screws (60x 1.0x3mm, 60x 1.0x5mm, 60x 1.0x8mm, 60x 1.5x4mm, 60x 1.5x6mm, 60x 1.5x8mm, 60x 2.0x5mm, & 60x 2.0x8mm) Set also comes with a 20 piece drillset with HSS titanium covered drills covering 0.3 to 1.6mm. NOTES - screws are now BLACK in colour - Packaging can vary and might be slightly different from image
Digital Accessory and Point Decoder
Digital Accessory and Point Decode - Can only be used with Hornby Select and Elite Controllers - Powers 4 individual accessories - OO Scale
E-Z Command 8 Pin To 21 Pin Adaptor
8 Pin To 21 Pin Adaptor Enables use of 8-pin deocder in 21-pin DCC Ready loco's
Flexi Loco Lift (Double) N,OO/HO,OO9/HOe,EM, TT Scale
Flexi Loco Lift (Double) N,OO/HO,OO9/HOe,EM, TT Scale Designed - To carry small to larger OO locomotives (steam tank engine or Diesel Shunter) or - Large N scale Locomotives and full rakes of trains - Width can be adjusted to suit your scale - Modular system means they can be stacked and extended to cater for your storage and operating needs - Scales N,OO/HO,OO9/HOe,EM, TT.
Flexi Loco Lift (Single) Designed - To carry small OO locomotives (steam tank engine or Diesel Shunter) or - Large N scale Locomotives - Width can be adjusted to suit your scale - Modular system means they can be stacked and extended to cater for your storage and operating needs - Scales N (2mm) - TT (3mm) - OO (4mm)
Four Pole Double Throw Toggle Switch (for use with SL-E383F)
Four Pole Double Throw Toggle Switch (for use with SL-E383F)
Green Wire (7 x 0.2mm) 10m
Grey Wire (7 x 0.2mm) 10m
HM7000-21TXS: Bluetooth® & DCC Sound Decoder (21-pin)
HM7000-21TXS: Bluetooth® & DCC Sound Decoder (21-pin) For use with HM7000 APP
HM7000-6: Bluetooth® & DCC Decoder (6-pin)
HM7000-6: Bluetooth® & DCC Decoder (6-pin) For use with HM7000 APP
HM7000-8TXS: Bluetooth® & DCC Sound Decoder (8-pin)
HM7000-8TXS: Bluetooth® & DCC Sound Decoder (8-pin) For use with HM7000 APP
HM7000-N18TXS: Bluetooth® & DCC Sound Decoder (Next18-pin)
HM7000-N18TXS: Bluetooth® & DCC Sound Decoder (Next18-pin)
HM7020: 15V Power Supply Adapter
HM7020: 15V Power Supply Adapter This Adapter allows you to use an existing power supply with the HM7000 system
HM7040: Bluetooth® Legacy Dongle
HM7040: Bluetooth® Legacy Dongle This connects to existing Hornby Select or Elite and allows non Bluetooth® decoders to be controlled via the HM7000 APP
HM7070 - Power Bank Stay-alive for use with HM7000 decoders
Imperium 21 Pin 8 Function Decoder
Dapol - Imperium 21 Pin 8 Function Decoder
Imperium 21 Pin MTC 6 Function Decoder
Dapol - Imperium 21 Pin MTC 6 Function Decoder
Inter-Baseboard Connectors (2 Pack)
Inter-Baseboard Connectors (2 Pack) These clever pluggable screw-terminal connectors allow you to easily connect baseboard power with plug-and-socket connections! Suitable for DC or DCC on systems up to 5 Amps. Includes: - 2x Pluggable Screw-Terminal Connectors - Ferruled Connector Wire - Fixing Screws - Spare Ferrules (will require a crimping tool to use the spares)
Large Width Couplings (Pack 10)
Large Width Couplings (Pack 10) - OO scale
LEDs 10 Green - 10 Red - & 20 Panel Clips
LEDs 10 Green - 10 Red - & 20 Panel Clips
Legacy Wired Joiners Code 100 Rail Pack of 6x Pairs
Legacy Wired Joiners Code 100 Rail Pack of 6x Pairs 300mm high quality track feed wires pre-soldered to Legacy Rail Joiners. Compatible with Code 100 track from Legacy and equivalent track from all major brands. Super-quick and easy to use – no soldering necessary! Pack contains 6 pairs - OO Scale
Legacy Wired Rail Joiners Code 75 Track Pack of 6x Pairs
Legacy Wired Rail Joiners Code 75 Track Pack of 6x Pairs 300mm high quality track feed wires pre-soldered to Legacy Rail Joiners. Compatible with Code 75 track from Legacy and equivalent track from all major brands. Super-quick and easy to use – no soldering necessary! Pack contains 6 pairs - OO Scale
LM-PP.2 Legacy Models Powerpoint Dowels 2x Pack
DCC Concepts - LM-PP.2 Legacy Models Powerpoint Dowels 2x Pack Wire-Free Baseboard connections Easily installed, super-accurate alignment dowels that remove the need for wires! PowerPoint dowels are a dream come true. Highly accurate, they can both transmit track power and perfectly align your baseboards. All of the electrial parts are gold plated too, so they'll never fail you! PowerPoints can confortably handle far more power than a DCC system can deliver, so you will only need to use one pair to reliably transfer power between average baseboards. Work carefully and you will obtain a great result when installing your new Legacy PowerPoint Dowels Clamp the baseboard ends together. Be sure the top surfaces are perfectly level and aligned. (You can temporarily screw an offcut of wood over the top of joint to ensure it is perfect) Mark the position for the dowels. Drill a pilot hole right through both ends using a 3mm drill. (keep it at 90 degrees to the board faces as this step will guide all subsequent drilling) Separate the two boards. Use a 19mm spade drill bit, and go just deep enough into the front face of each board end (2mm) (This is about right to allow the flange of the dowel to sit flush with the baseboard ends) Now, using a 13mm spade drill bit and working from the other side, drill right through the board. You will now have a 13mm hole with a 19mm flange. (Clean it up and remove anu rough edges and sawdust to make it ready for the Dowell installation) Add a little PVA to the grooves in each dowel & insert it flush with the face of the board. (If it’s too tight for a firm push-fit, ream the hole with sandpaper. Do NOT tap them in as you may damage them) To secure boards together after alignment, drill clearance holes for 1/4” bolts & wingnuts. (They do not need to be tight as the dowels will do all the work of aligning the boards perfectly) Connect the track power wires. Your PowerPoints are now installed and ready! By the way...PowerPoints will carry more than 5 amps of track power, so you will not overload them - ever!. Only top quality materials are used. The electrical parts are all gold plated so they will never tarnish and lose conductivity. PowerPoints can also be disassembled for cleaning or lubrication if needed, and we even supply you with spare parts in the pack. They really ARE designed to last forever!
LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack
DCC Concepts - LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack Wire-Free Baseboard connections Easily installed, super-accurate alignment dowels that remove the need for wires! PowerPoint dowels are a dream come true. Highly accurate, they can both transmit track power and perfectly align your baseboards. All of the electrial parts are gold plated too, so they'll never fail you! PowerPoints can confortably handle far more power than a DCC system can deliver, so you will only need to use one pair to reliably transfer power between average baseboards. Work carefully and you will obtain a great result when installing your new Legacy PowerPoint Dowels Clamp the baseboard ends together. Be sure the top surfaces are perfectly level and aligned. (You can temporarily screw an offcut of wood over the top of joint to ensure it is perfect) Mark the position for the dowels. Drill a pilot hole right through both ends using a 3mm drill. (keep it at 90 degrees to the board faces as this step will guide all subsequent drilling) Separate the two boards. Use a 19mm spade drill bit, and go just deep enough into the front face of each board end (2mm) (This is about right to allow the flange of the dowel to sit flush with the baseboard ends) Now, using a 13mm spade drill bit and working from the other side, drill right through the board. You will now have a 13mm hole with a 19mm flange. (Clean it up and remove anu rough edges and sawdust to make it ready for the Dowell installation) Add a little PVA to the grooves in each dowel & insert it flush with the face of the board. (If it’s too tight for a firm push-fit, ream the hole with sandpaper. Do NOT tap them in as you may damage them) To secure boards together after alignment, drill clearance holes for 1/4” bolts & wingnuts. (They do not need to be tight as the dowels will do all the work of aligning the boards perfectly) Connect the track power wires. Your PowerPoints are now installed and ready! By the way...PowerPoints will carry more than 5 amps of track power, so you will not overload them - ever!. Only top quality materials are used. The electrical parts are all gold plated so they will never tarnish and lose conductivity. PowerPoints can also be disassembled for cleaning or lubrication if needed, and we even supply you with spare parts in the pack. They really ARE designed to last forever!
Loco Servicing Cradle - for N - OO/HO & OO-9
Locomotive Servicing Cradle - Foam tray designed to carefully hold your chosen model whilst you perform Maintenance
Medium Width Couplings (Pack 10)
Medium Width Couplings (Pack 10) - OO scale
Microswitch enclosed type - Designed to fit into O Gauge points in the tie-bar housing - The switch is designed to operate the polarity of electrofrog point work
Microswitch Housing - (for SLE790BH)
Microswitch Housing - (for SLE790BH)
Motor Adaptor - For fitting to PL10 Point motors - OO Scale
Mounting Plates for use with PL10
Mounting Plates - Designed for solenoid Point motor PL10E (extended Pin Motor) for underneath the baseboard mounting - The point motor sits into the mounting plate via the extended legs on the motor (these are than twisted using fine pliers or tweezers to secure motor to the mounting plate) - Comes with self tapping wood screws to secure mounting plate to baseboard
N Scale Loco Crankpin Box Spanner
N Scale Loco Crankpin Box Spanner A handy addition to any N scale modeller’s tool kit, this Loco Crankpin Box Spanner is an essential tool for maintaining your cherished Graham Farish models. Made of machined metal, this tool is specially designed for removing the crankpins from Graham Farish steam locomotives, you can quickly and easily change the driving wheel traction tyres to keep your models in prime running condition for years to come.
N Scale Westinghouse Cosmetic Point Motors (12)
DCC Concepts -N Scale Westinghouse Cosmetic Point Motors (12) 12x N Scale Westinghouse Motors True-scale, high quality models of the Westinghouse EP Pneumatic Point Motor. Widely used in the UK, Australia and parts of Europe. These accurate representations make a real difference when added to your layout and are the perfect partner for our Cobalt motors!
NCE Power Cab DCC Starter Set An entire DCC system in the palm of your hand! This 2 Amp system can operate up to 4 OO sized locomotives or 8 N gauge trains. This cab provides all of the capability and ease of use that you’ve heard about in our Power Pro system, at an entry level price. Installation is a snap. Hook two wires to your track and plug in the cab. You’re off and running trains! The Power Cab kit contains: NCE Power Cab 7' Power Cab Cable PCP Power Panel EU / UK Approved Power Supply Pro Cab Coiled Cord Manual.
NEM Couplings (Pack 10) - OO scale
Next18 DCC Loco-Decoder (with Brake Button function)
Bachmann Next18 DCC Loco-Decoder (with Brake Button function) - F2 on your DCC controller will activate break function (in the case of sound fitted locomotives you will hear brake sounds too) - Pressing F2 down will bring the locomotive to a complete standstill
On-Off Switch (style matches PL26 series)
On-Off Switch (style matches PL26 series)
On-On Changeover Switch (style matches PL26 series)
On-On Changeover Switch (style matches PL26 series)
OO Scale Westinghouse Cosmetic Point Motors (12)
DCC Concepts -OO Scale Westinghouse Cosmetic Point Motors (12) 12x OO/HO Scale Westinghouse Motors True-scale, high quality models of the Westinghouse EP Pneumatic Point Motor. Widely used in the UK, Australia and parts of Europe. These accurate representations make a real difference when added to your layout and are the perfect partner for our Cobalt motors.
Orange Wire (7 x 0.2mm) 10m
Pack of 48 Assorted Links for Cobalt-SS (12 each, 4 types)
DCC Concepts - Pack of 48 Assorted Links for Cobalt-SS (12 each, 4 types) - Any Scale Custom linkage for Cobalt-SS motors - use these to link your Cobalt-SS motor to your point or turnout. Each pack contains 48 links, 12 each of 4 different types.
Passing Contact Switch - Black Lever
Passing Contact Switch - Black Lever
Passing Contact Switch - Red Lever
Passing Contact Switch - Red Lever
Passing Contact Switch - White Lever
Passing Contact Switch - White Lever
Passing Contact Switch - Yellow Lever
Passing Contact Switch - Yellow Lever
Pink Wire (7 x 0.2mm) 10m
PL1000 TwistLock Motor - Designed to make attachment under a baseboard easier. Includes: - template to align the Solenoid motor in position easily - Self tapping screws - Suitable for N up to O Gauge
PL1005 TwistLock Microswitch - Designed to be installed on a PL1000 Twistlock solenoid motor for use with Electrofrog Points - Wires can be either crimped on to the terminals or soldered - Suitable for use with Electrofrog points
PL38B Wire - Blue - 7 Metre Reel - 3 Amp Current Rating
PL38BK Wire - Black - 7 Metre Reel - 3 Amp Current Rating
PL38G Wire - Green - 7 Metre Reel - 3 Amp Current Rating
PL-38R Wire - Red - 7 Metre Reel - 3 Amp Current Rating
PL38Y Wire - Yellow - 7 Metre Reel - 3 Amp Current Rating
Plux22 DCC Loco-Decoder (with Brake Button function) (36-570A)
Plux22 DCC Loco-Decoder (with Brake Button function) Features: - A Plux22 (NEM658) DCC Decoder suitable for models fitted with a Plux22 DCC decoder socket. - Multi-mode (NMRA-DCC format, Motorola protocol, DC Analogue and AC Analogue (Marklin)) with Back EMF function - 11 function outputs (9 powered and 2 logic level) - 1.2A continuous load - Suitable for models equipped with DC motors (including coreless motors) - Dimension: 22mm x 15mm x 3.5mm
Pocket Coupling (Pack 10) - OO scale
Solenoid Point Motor - Requires power and switch to operate (Sold individually) - OO scale
Point Motor Passing Contact Switch - Black
Point Motor Passing Contact Switch - For operating points and accessories - Black Colour - OO Accessory
Point Motor Wire Red/Green/Black Tripled (14 x 0.15) 10m
Point Motor Wire Red/Green/Black Tripled (14 x 0.15) 10m For use with Solenoid Point motors or SEEP Point motors
Power Feed Joiners For C100 - C124 Rail (4 pairs)
Power Feeds - Designed for Code 100 OO Gauge track including (Setrack and Code 124 O Gauge Tracks) - 4 Pairs included
Power Feed Joiners For C55 - C80 Rail (4 pairs)
Power Feeds - Designed for Code 55 and 80 N Gauge Tracks - 4 Pairs
Power Feed Joiners For C70 - C75 - C83Rail (4 pairs)
Power Feeds - Designed for Code 75 OO Gauge Track (Including Code 70 and Code 83) - 4 Pairs
Power-Lube - liquid lubricant and cleaner
Power Lube - For lubrication of your locomotives and working accessories - DO NOT put too much lube on locomotive axles when servicing (this will result in a static effect to dust and dirt particles and cause them to clog up moving parts)
Precision Lubricator with Needle Applicator (10ml)
Precision Lubricator with Needle Applicator (10ml)
Probe for operating turnout motors (use with PL18)
Probe for operating turnout motors (use with PL18)
Rail Cleaner - abrasive rubber block
Rail Cleaner - The abrasive block is rubbed along the top surface of the rails to clean any dirt that will stop/disturb electrical connection of your model locomotives/ accessories (thus leading to poor operation) - IMPORTANT not to press too hard on the track (always better to take a few passes with the rubber than in one go) - Always be gently around point work whilst cleaning otherwise you could damage the point blades and tie-bar (switch mechanism)
Red Wire (7 x 0.2mm) 10m
Red/Black Twinned Wire (14 x 0.15mm) 10m
Red/Black Twinned Wire - Diameter (14 x 0.15mm) - Total length of cable is 10m - Ideal for track wiring needing two cables at a time.
Ruby Series 2fn Small DCC Decoder 8 Pin
Ruby Series 2fn Small DCC Decoder 8 Pin The DCC92 is a 8 pin decoder with a fitted 45mm harness between the pins and the decoder. An ideal decoder for retrofitting into non DCC Ready locomotives. Features: 2 Digit and 4 Digit Addressing 14, 28 or 128 Speed Steps Smooth Operation Constant Brightness Lighting Direct Mode Programming Motor Isolation Protection Advanced Consisting
Ruby Series 2fn Standard DCC Decoder 21 Pin
Ruby Series 2fn Standard DCC Decoder 21 Pin Includes - 2 Digit and 4 Digit Addressing - 14, 28 or 128 Speed Steps - Smooth Operation - Constant Brightness Lighting - Direct Mode Programming - Motor Isolation Protection - Advanced Consisting - Socket to Add PowerPal - Current Rating 0.5Amps - Motor Rating 1.5 - 2 Amps
Seep Point Motor with Built-In Switch
Seep Point Motor with Built-In Switch - Ideal for electrofrog points to change polarity at the same time as the tiebar - OO and N gauge
Seep Point Motor with Latching Mechanism
Seep Point Motor with Latching Mechanism Seep Point Motors have the advantage of being easy to fix under the baseboard, requiring only a small slot to operate the point. The PM-4 is our best point motor for throwing points that have lost the over centre spring or are a bit heavy to move. It also features a change over switch for changing polarity and LEDs if required. Includes: - 1x GMC-PM4 Solenoid Motor - Instructions for installation and wiring - OO, O Scale
PL11 Side-mounted Motor - Designed to be placed alongside Peco Points to throw the point rails - Can be used with Electrofrog points but another type of switch will be required to change the polarity - OO Gauge
Single Track Walkabout Controller
Single Track Walkabout Controller Designed for those who wish to walk around there layouts or operate from afar - Designed to be wired with a Gaugemaster GM75 Plug and socket for panel mounting - Can be powered via: GMC-M1 Transformer, GMC-T1 Transformer, GMC-WM1 Transformer - Suitable for N,OO and OO9 Gauges
Slim Vertical Mounted Magnetic Sensors (3-pack)
DCC Concepts - Slim Vertical Mounted Magnetic Sensors (3-pack) These detectors have been designed to be very easy to install. Super-slim at only 4mm in diameter, they will fit comfortably between the sleepers of DCCconcepts and Peco Code 100 and Code 75 track as well as most other brands of track in HO. (N scale users will need to temporarily move a sleeper while drilling, but will also find installation quite easy). They are Normally Off and are triggered or turned on by a small magnet that is attached to the loco or rolling stock. While it is always good to use smaller magnets and get the magnet as close as possible to any sensor such as this, we find that even with quite a small magnet we can get reliable results from up to 10mm away. Ideal for all detection and to trigger devices such as Cobalt Point Motors or Alpha. The connector is supplied so that the detectors can be used with our ADiA range of Accessory Decoders. Length of sensor: 15mm Width of sensor: 4mm Length of wire: 300mm Quantity in pack: 3 (Was DCP-TMS) Please note these are Normally Off or Normally Open momentary type connections
Smart Frog unit - Designed to change Polarity on Electrofrog points whilst using the PLS100 SmartSwitch Set
Standard 6 pin Decoder
Standard 8 pin Locomotive Decoder
Standard 8 pin Locomotive Decoder
Standard Wall Plug Mains Transformer
Standard Wall Plug Mains Transformer - Input: 230v Mains - Output: 12v DC - OO Accessory
Studs and Tag Washers - for use with probe
Studs and Tag Washers - for use with probe (PL17)
Track Isolating Switch - Place between two sections of track to isolate one from the other - Used on Analogue railways to park up more than one locomotive on a section of track (like in engine sheds, station bay platforms)
Tracklayers Tool set A specially selected tool set from expert modellers here at PECO for laying track. These tools are vital to all modellers, included also is expert knowledge in the form a useful guide brought to you by the experts at Railway Modeller. Includes: Xuron track cutters Snipe nose pliers Snap-off knife with 10 spare blades Set of 4 needle files Pin vice Drill bits: 0.5 to 2.5 mm A4 cutting mat Sharpie marker pen Track pin pusher PECO track pins PECO rail cleaner Shows you how guide: 'Laying the track'
PL-10 Turnout Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases or directly underneath a Peco point - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales
PL10E Extended Pin Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases underneath the baseboard - Pin might require cutting to length once installed (depending on baseboard thickness) - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales
Turnout Switch Module (add on) - This module clips into either PL50 or other PL51 Switch Module units - Designed so you can expand your switching requirements to your chosen design. - Peco Electrics
Turntable motor and control system Ideal for anyone updating an older motor drive or converting a manual drive turntable into electric. This is a "NON Indexing" motor system meaning it has no pre set alignment programs, offering ultimate flexibility without any rewiring of your layout. Includes - Motor Unit and fixing Lugs - Hand Held Controller - Wire and fixings - Manual of instructions - Requires power supply from a 12VDC 2Amp Supply NOT included - OO and N Scale Peco Turntables
Twin Micro Switch Kit - for fitting to turnout motor PL10
Twin Micro Switch Kit - for fitting to turnout motor PL10
Twin Track Cased Controller Ideal for expanding the train set with the ability to control 2x locomotives independantly and power accessories - All in one controller with power lead wired - Sturdy Metal Casing - Accessory outputs ideal for point motors - Requires connecting to the mains via the socket - Suitable for N, OO and OO9 Gauges
Wall Mounted Transformer 1 x 16v AC or 12v DC @ 0.75 Amps
Wall Mounted Transformer Ideal for smaller Layouts or powering point motors ad acessories Includes - Outputs: 1 x 16v AC and 12v DC - Current Rating: 0.75 Amps - Mains transformer - Suitable for N,OO and OO9 Gauges
Wheel cleaning Scraper - Designed to clean your locomotive wheels and be used alongside PL42 wheel Cleaning Brush - Can be provided with an electrical charge (from your controller) to spin the locomotive wheels and rub off dirt as they turn round. - DO NOT use this brush on a locomotive fitted with traction tyres or on the wheels with traction tyres as you will rip and destroy the tyres
White Wire (7 x 0.2mm) 10m
Wiring Loom
Yellow Wire (7 x 0.2mm) 10m
Zen 3-Wire Medium Stay Alive for Zen Black & Blue+ Decoders
Zen 3-Wire Medium Stay Alive for Zen Black & Blue+ Decoders A single medium Stay-Alive with 3-wire connections to the decoder. Totally Plug and Play with Zen decoders. Usable with Zen Black, Zen Blue+, Lenz and ESU or any decoder with three-wire connections for Stay-Alive. Please note that connection of a DCCconcepts Zen Stay-Alive to a non-DCCconcepts decoder may invalidate your warranty, please check documentation which came with your decoder for details.
Zen Black Classic Small Decoder 8-pin harness + ABC module
Zen Black Classic Small Decoder 8-pin harness + ABC module Zen decoder software has always been smooth, clever and easy to use but our new BLACK decoder range takes this to a new level, with extended and improved automatic braking and shuttle abilities, simple-to-use ONE step locomotive set-up and advanced brown-out protection. All of our decoders are tested at least 3 times before we package them for sale, so we know that they all work perfectly when we sell them and you can be quite confident that reliability is assured. This pack includes 1x ABC board to use with automatic braking functionality. Decoder features: 1.1 Amps peak power 750mA continuous power 4 functions at 100mA each 19mm x 11mm x 6mm 8-pin & harness One-Step Loco Setup Shuttle mode (requires ABC boards for this to function) Stay-Alive connection
Zen Blue+ Direct 6-pin 2 function
Zen Blue+ Direct 6-pin 2 function Zen decoder software has always been smooth, clever and easy to use but our new decoder range takes this to a new level, with simple-to-use ONE step locomotive set-up and advanced brown-out protection. All of our decoders are tested at least 3 times before we package them for sale, so we know that they all work perfectly when we sell them and you can be quite confident that reliability is assured. DCD-ZN6D.2 replaces the previous version - DCD-ZN6D. Decoder features: 1.1 Amps peak power 750mA continuous power 2 functions at 100mA each 14mm x 9mm x 3.5mm 6-pin direct One-Step Loco Setup