Accessory Switch - for fitting to turnout motor PL10
Accessory Switch (mounts on top of PL10 and PL10E Point motors) - Designed to change the polarity of Electrofrog points - OO Gauge
Adaptor Base - Self Assemble No Spring
Adaptor Base for PL10 point motors - Self Assemble No Spring - For use with self latching points - OO Gauge
Cable Clips - self adhesive - Help tidy and neaten wiring under your railway
Capacitor Discharge Unit (CDU)
Capacitor Discharge Unit (CDU) - This device is for use with Solenoid Point motors (PL10 / PL10E/ PL11) - The CDU is designed to store and release electrical power. When you switch your point blades (via switch like PL26 R/B/W/Y), the extra power ensures the blades throw properly every time. - The CDU requires a 16V Accessory out put either from your controller or via a separate accessory transformer (recommend Gaugemaster GMC WM1 Wall mounted transformer)
Connectors/Shrouds 10 connectors - 5 shrouds
Connectors/Shrouds Includes - 10 Connectors - 5 shrouds Designed to join on the terminals of Point Motors (PL10/ PL10E etc) to eliminate soldering
Flexi Loco Lift (Single) Designed - To carry small OO locomotives (steam tank engine or Diesel Shunter) or - Large N scale Locomotives - Width can be adjusted to suit your scale - Modular system means they can be stacked and extended to cater for your storage and operating needs - Scales N (2mm) - TT (3mm) - OO (4mm)
Four Pole Double Throw Toggle Switch (for use with SL-E383F)
Four Pole Double Throw Toggle Switch (for use with SL-E383F)
LEDs 10 Green - 10 Red - & 20 Panel Clips
LEDs 10 Green - 10 Red - & 20 Panel Clips
Loco Servicing Cradle - for N - OO/HO & OO-9
Locomotive Servicing Cradle - Foam tray designed to carefully hold your chosen model whilst you perform Maintenance
Microswitch enclosed type - Designed to fit into O Gauge points in the tie-bar housing - The switch is designed to operate the polarity of electrofrog point work
Microswitch Housing - (for SLE790BH)
Microswitch Housing - (for SLE790BH)
Motor Adaptor - For fitting to PL10 Point motors - OO Scale
Mounting Plates for use with PL10
Mounting Plates - Designed for solenoid Point motor PL10E (extended Pin Motor) for underneath the baseboard mounting - The point motor sits into the mounting plate via the extended legs on the motor (these are than twisted using fine pliers or tweezers to secure motor to the mounting plate) - Comes with self tapping wood screws to secure mounting plate to baseboard
On-Off Switch (style matches PL26 series)
On-Off Switch (style matches PL26 series)
On-On Changeover Switch (style matches PL26 series)
On-On Changeover Switch (style matches PL26 series)
Passing Contact Switch - Black Lever
Passing Contact Switch - Black Lever
Passing Contact Switch - Red Lever
Passing Contact Switch - Red Lever
Passing Contact Switch - White Lever
Passing Contact Switch - White Lever
Passing Contact Switch - Yellow Lever
Passing Contact Switch - Yellow Lever
PL1000 TwistLock Motor - Designed to make attachment under a baseboard easier. Includes: - template to align the Solenoid motor in position easily - Self tapping screws - Suitable for N up to O Gauge
PL1005 TwistLock Microswitch - Designed to be installed on a PL1000 Twistlock solenoid motor for use with Electrofrog Points - Wires can be either crimped on to the terminals or soldered - Suitable for use with Electrofrog points
PL38B Wire - Blue - 7 Metre Reel - 3 Amp Current Rating
PL38BK Wire - Black - 7 Metre Reel - 3 Amp Current Rating
PL38G Wire - Green - 7 Metre Reel - 3 Amp Current Rating
PL-38R Wire - Red - 7 Metre Reel - 3 Amp Current Rating
PL38Y Wire - Yellow - 7 Metre Reel - 3 Amp Current Rating
Power Feed Joiners For C100 - C124 Rail (4 pairs)
Power Feeds - Designed for Code 100 OO Gauge track including (Setrack and Code 124 O Gauge Tracks) - 4 Pairs included
Power Feed Joiners For C55 - C80 Rail (4 pairs)
Power Feeds - Designed for Code 55 and 80 N Gauge Tracks - 4 Pairs
Power Feed Joiners For C70 - C75 - C83Rail (4 pairs)
Power Feeds - Designed for Code 75 OO Gauge Track (Including Code 70 and Code 83) - 4 Pairs
Power-Lube - liquid lubricant and cleaner
Power Lube - For lubrication of your locomotives and working accessories - DO NOT put too much lube on locomotive axles when servicing (this will result in a static effect to dust and dirt particles and cause them to clog up moving parts)
Probe for operating turnout motors (use with PL18)
Probe for operating turnout motors (use with PL18)
Rail Cleaner - abrasive rubber block
Rail Cleaner - The abrasive block is rubbed along the top surface of the rails to clean any dirt that will stop/disturb electrical connection of your model locomotives/ accessories (thus leading to poor operation) - IMPORTANT not to press too hard on the track (always better to take a few passes with the rubber than in one go) - Always be gently around point work whilst cleaning otherwise you could damage the point blades and tie-bar (switch mechanism)
PL11 Side-mounted Motor - Designed to be placed alongside Peco Points to throw the point rails - Can be used with Electrofrog points but another type of switch will be required to change the polarity - OO Gauge
Smart Frog unit - Designed to change Polarity on Electrofrog points whilst using the PLS100 SmartSwitch Set
Studs and Tag Washers - for use with probe
Studs and Tag Washers - for use with probe (PL17)
Track Isolating Switch - Place between two sections of track to isolate one from the other - Used on Analogue railways to park up more than one locomotive on a section of track (like in engine sheds, station bay platforms)
PL-10 Turnout Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases or directly underneath a Peco point - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales
PL10E Extended Pin Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases underneath the baseboard - Pin might require cutting to length once installed (depending on baseboard thickness) - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales
Turnout Switch Module (add on) - This module clips into either PL50 or other PL51 Switch Module units - Designed so you can expand your switching requirements to your chosen design. - Peco Electrics
Turntable motor and control system Ideal for anyone updating an older motor drive or converting a manual drive turntable into electric. This is a "NON Indexing" motor system meaning it has no pre set alignment programs, offering ultimate flexibility without any rewiring of your layout. Includes - Motor Unit and fixing Lugs - Hand Held Controller - Wire and fixings - Manual of instructions - Requires power supply from a 12VDC 2Amp Supply NOT included - OO and N Scale Peco Turntables
Twin Micro Switch Kit - for fitting to turnout motor PL10
Twin Micro Switch Kit - for fitting to turnout motor PL10
Wheel cleaning Scraper - Designed to clean your locomotive wheels and be used alongside PL42 wheel Cleaning Brush - Can be provided with an electrical charge (from your controller) to spin the locomotive wheels and rub off dirt as they turn round. - DO NOT use this brush on a locomotive fitted with traction tyres or on the wheels with traction tyres as you will rip and destroy the tyres
Wiring Loom