NCE Power Cab DCC Starter Set

NCE Power Cab DCC Starter Set An entire DCC system in the palm of your hand! This 2 Amp system can operate up to 4 OO sized locomotives or 8 N gauge trains. This cab provides all of the capability and ease of use that you’ve heard about in our Power Pro system, at an entry level price. Installation is a snap. Hook two wires to your track and plug in the cab. You’re off and running trains!   The Power Cab kit contains: NCE Power Cab 7' Power Cab Cable PCP Power Panel EU / UK Approved Power Supply Pro Cab Coiled Cord Manual.  

DCC Concepts Zen Blue+ Direct 6-pin 2 function

Zen Blue+ Direct 6-pin 2 function Zen decoder software has always been smooth, clever and easy to use but our new decoder range takes this to a new level, with simple-to-use ONE step locomotive set-up and advanced brown-out protection. All of our decoders are tested at least 3 times before we package them for sale, so we know that they all work perfectly when we sell them and you can be quite confident that reliability is assured. DCD-ZN6D.2 replaces the previous version - DCD-ZN6D. Decoder features: 1.1 Amps peak power 750mA continuous power 2 functions at 100mA each 14mm x 9mm x 3.5mm 6-pin direct One-Step Loco Setup  

DCC Concepts Zen Black Classic Small Decoder 8-pin harness + ABC module

Zen Black Classic Small Decoder 8-pin harness + ABC module Zen decoder software has always been smooth, clever and easy to use but our new BLACK decoder range takes this to a new level, with extended and improved automatic braking and shuttle abilities, simple-to-use ONE step locomotive set-up and advanced brown-out protection. All of our decoders are tested at least 3 times before we package them for sale, so we know that they all work perfectly when we sell them and you can be quite confident that reliability is assured. This pack includes 1x ABC board to use with automatic braking functionality.   Decoder features: 1.1 Amps peak power 750mA continuous power 4 functions at 100mA each 19mm x 11mm x 6mm 8-pin & harness One-Step Loco Setup Shuttle mode (requires ABC boards for this to function) Stay-Alive connection

DCC Concepts Slim Vertical Mounted Magnetic Sensors (3-pack)

DCC Concepts - Slim Vertical Mounted Magnetic Sensors (3-pack) These detectors have been designed to be very easy to install. Super-slim at only 4mm in diameter, they will fit comfortably between the sleepers of DCCconcepts and Peco Code 100 and Code 75 track as well as most other brands of track in HO. (N scale users will need to temporarily move a sleeper while drilling, but will also find installation quite easy). They are Normally Off and are triggered or turned on by a small magnet that is attached to the loco or rolling stock. While it is always good to use smaller magnets and get the magnet as close as possible to any sensor such as this, we find that even with quite a small magnet we can get reliable results from up to 10mm away. Ideal for all detection and to trigger devices such as Cobalt Point Motors or Alpha. The connector is supplied so that the detectors can be used with our ADiA range of Accessory Decoders. Length of sensor: 15mm Width of sensor: 4mm Length of wire: 300mm Quantity in pack: 3 (Was DCP-TMS) Please note these are Normally Off or Normally Open momentary type connections

DCC Concepts LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack

DCC Concepts - LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack Wire-Free Baseboard connections Easily installed, super-accurate alignment dowels that remove the need for wires! PowerPoint dowels are a dream come true. Highly accurate, they can both transmit track power and perfectly align your baseboards. All of the electrial parts are gold plated too, so they'll never fail you! PowerPoints can confortably handle far more power than a DCC system can deliver, so you will only need to use one pair to reliably transfer power between average baseboards. Work carefully and you will obtain a great result when installing your new Legacy PowerPoint Dowels Clamp the baseboard ends together. Be sure the top surfaces are perfectly level and aligned. (You can temporarily screw an offcut of wood over the top of joint to ensure it is perfect) Mark the position for the dowels. Drill a pilot hole right through both ends using a 3mm drill. (keep it at 90 degrees to the board faces as this step will guide all subsequent drilling) Separate the two boards. Use a 19mm spade drill bit, and go just deep enough into the front face of each board end (2mm) (This is about right to allow the flange of the dowel to sit flush with the baseboard ends) Now, using a 13mm spade drill bit and working from the other side, drill right through the board. You will now have a 13mm hole with a 19mm flange. (Clean it up and remove anu rough edges and sawdust to make it ready for the Dowell installation) Add a little PVA to the grooves in each dowel & insert it flush with the face of the board. (If it’s too tight for a firm push-fit, ream the hole with sandpaper. Do NOT tap them in as you may damage them) To secure boards together after alignment, drill clearance holes for 1/4” bolts & wingnuts. (They do not need to be tight as the dowels will do all the work of aligning the boards perfectly) Connect the track power wires. Your PowerPoints are now installed and ready! By the way...PowerPoints will carry more than 5 amps of track power, so you will not overload them - ever!. Only top quality materials are used. The electrical parts are all gold plated so they will never tarnish and lose conductivity. PowerPoints can also be disassembled for cleaning or lubrication if needed, and we even supply you with spare parts in the pack. They really ARE designed to last forever!

Peco Tracklayers Tool set

Tracklayers Tool set A specially selected tool set from expert modellers here at PECO for laying track. These tools are vital to all modellers, included also is expert knowledge in the form a useful guide brought to you by the experts at Railway Modeller. Includes: Xuron track cutters Snipe nose pliers Snap-off knife with 10 spare blades Set of 4 needle files Pin vice Drill bits: 0.5 to 2.5 mm A4 cutting mat Sharpie marker pen Track pin pusher PECO track pins PECO rail cleaner Shows you how guide: 'Laying the track'

Hornby HM7070 - Power Bank

HM7070 - Power Bank Stay-alive for use with HM7000 decoders

DCC Concepts DCD-ZNmini.4 Zen Black Decoder Mini 8Pin

DCD-ZNmini.4 Zen Black Decoder Mini 8Pin Includes – 1.1 Amps peak power– 750mA continuous power– 4 functions at 100mA each– 19mm x 11mm x 6mm– 8-pin & harness– One-Step Loco Setup– Shuttle mode (requires ABC boards for this to function)– Brown-Out Protection on-board– Stay-Alive connection

DCC Concepts DCD-ZBHP.6 Zen Black Buddha Decoder O & Larger Scale

DCD-ZBHP.6 Zen Black Buddha Decoder O & Larger Scale Includes  – 5 Amps peak power– 3 Amps continuous power– 6 functions at 250mA each– On-board high-power stay-alive– 42mm x 27mm x 13mm– 12 screw terminals– One-Step Loco Setup– Shuttle mode (requires ABC boards for this to function)

DCC Concepts DCD-ZN68.2 Zen Blue+Decoder NEM651 6-Pin Direct/ Harness 2 Funct

DCD-ZN68.2 Zen Blue+Decoder NEM651 6-Pin Direct/ Harness 2 Funct Includes - 1.1Amps Peak Power - 750mA Continuous power - 2 Functions at 100mA each - Dimensions 13.5mm x 8.5mm - 6 PIN Direct, 6 PIN Harness and 8 PIN Harness - One step loco setup  

Gaugemaster Red/Black Twinned Wire (14 x 0.15mm) 10m

Red/Black Twinned Wire - Diameter (14 x 0.15mm) - Total length of cable is 10m - Ideal for track wiring needing two cables at a time.

Gaugemaster Seep Point Motor with Built-In Switch

Seep Point Motor with Built-In Switch - Ideal for electrofrog points to change polarity at the same time as the tiebar - OO and N gauge