DCC Concepts Cobalt iP Digital Point Motor (Single)

Cobalt iP Digital Point Motor (Single) - Any Scale Includes: - 1x Digital Point motor - Instruction manual  - Product Size:   - Width 28.5mm (67mm over the mounting wings)   - Depth 40mm (48mm over the mounting wings)   - Height 44mm (67mm over the connector) - Bag of attachments Features: The Cobalt-iP Digital’s super-low static current draw means very low power bus loading and the Cobalt-iP Digital is also able to cope with a very wide range of DC or DCC power supply voltages. We prefer 9~12V regulated power for DC, but any DCC voltage from 7 to 23 volts is acceptable. Cobalt-iP Digital is supplied with the throw bar already centred for easy installation. You can activate and de-activate self-centring and even swap the throw direction with a simple software command. This allows easy matching to layout needs, software driven computer displays, track diagrams or computer control. With Cobalt-IP “Intelligent Power” Digital Motors, you also have all the connection versatility you could ever need already built in. Frog power needs only one added wire, and a totally separate SPDT changeover switch can facilitate interlocking, control of signal feather indicators or ground signals, etc. Cobalt iP Digital also features the ability to add panel switches or control via DCC. The connection terminals used for panel switch connection are also able to give direct high/low state computer or DCC system feedback, so one motor really CAN do it all. Add to the above the ability to work with DC and super-simple wiring or DCC operation, or to combine digital and analog control… and Cobalt iP Digital really is the best choice for all layouts, no matter how you choose to power the trains!

Gaugemaster Black Wire (7 x 0.2mm) 100m

Black Wire (7 x 0.2mm) 100m This wire can be used for point motors, switches, track wiring and many other applications.

Gaugemaster Seep Point Motor with Built-In Switch

Seep Point Motor with Built-In Switch - Ideal for electrofrog points to change polarity at the same time as the tiebar - OO and N gauge

Gaugemaster Seep Point Motor with Latching Mechanism

Seep Point Motor with Latching Mechanism Seep Point Motors have the advantage of being easy to fix under the baseboard, requiring only a small slot to operate the point. The PM-4 is our best point motor for throwing points that have lost the over centre spring or are a bit heavy to move. It also features a change over switch for changing polarity and LEDs if required. Includes: - 1x GMC-PM4 Solenoid Motor - Instructions for installation and wiring - OO, O Scale   

Hornby Point Motor

Solenoid Point Motor - Requires power and switch to operate (Sold individually) - OO scale

Hornby Point Motor Passing Contact Switch - Black

Point Motor Passing Contact Switch - For operating points and accessories - Black Colour - OO Accessory

Peco Turnout Switch Module Add-on

Turnout Switch Module (add on) - This module clips into either PL50 or other PL51 Switch Module units - Designed so you can expand your switching requirements to your chosen design. - Peco Electrics

Peco Twin Micro Switch Kit - for fitting to turnout motor PL10

Twin Micro Switch Kit  - for fitting to turnout motor PL10

Peco Smart Frog

Smart Frog unit - Designed to change Polarity on Electrofrog points whilst using the PLS100 SmartSwitch Set

Peco Track Isolating Switch

Track Isolating Switch - Place between two sections of track to isolate one from the other - Used on Analogue railways to park up more than one locomotive on a section of track (like in engine sheds, station bay platforms)

Peco Turnout Motor (Extended Pin)

PL10E Extended Pin Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases underneath the baseboard  - Pin might require cutting to length once installed (depending on baseboard thickness) - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales

Peco Turnout Motor

PL-10 Turnout Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases or directly underneath a Peco point - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales

Peco Side-mounted Motor

PL11 Side-mounted Motor - Designed to be placed alongside Peco Points to throw the point rails - Can be used with Electrofrog points but another type of switch will be required to change the polarity - OO Gauge

Peco Rail Cleaner - abrasive rubber block

Rail Cleaner - The abrasive block is rubbed along the top surface of the rails to clean any dirt that will stop/disturb electrical connection of your model locomotives/ accessories (thus leading to poor operation) - IMPORTANT not to press too hard on the track (always better to take a few passes with the rubber than in one go) - Always be gently around point work whilst cleaning otherwise you could damage the point blades and tie-bar (switch mechanism) 

Peco PL1005 TwistLock Microswitch

PL1005 TwistLock Microswitch - Designed to be installed on a PL1000 Twistlock solenoid motor for use with Electrofrog Points - Wires can be either crimped on to the terminals or soldered  - Suitable for use with Electrofrog points

Peco On-Off Switch (style matches PL26 series)

On-Off Switch (style matches PL26 series)

Peco On-On Changeover Switch (style matches PL26 series)

On-On Changeover Switch (style matches PL26 series)

Peco Passing Contact Switch - Black Lever

Passing Contact Switch - Black Lever

Peco Passing Contact Switch - Red Lever

Passing Contact Switch - Red Lever

Peco Passing Contact Switch - White Lever

Passing Contact Switch - White Lever

Peco Passing Contact Switch - Yellow Lever

Passing Contact Switch - Yellow Lever

Peco Four Pole Double Throw Toggle Switch (for use with SL-E383F)

Four Pole Double Throw Toggle Switch (for use with SL-E383F)

Peco Microswitch enclosed type

Microswitch enclosed type - Designed to fit into O Gauge points in the tie-bar housing  - The switch is designed to operate the polarity of electrofrog point work

Peco Microswitch Housing - (for SLE790BH)

Microswitch Housing - (for SLE790BH)

Peco Accessory Switch - for fitting to turnout motor PL10

Accessory Switch (mounts on top of PL10 and PL10E Point motors) - Designed to change the polarity of Electrofrog points - OO Gauge

Peco Capacitor Discharge Unit (CDU)

Capacitor Discharge Unit (CDU) - This device is for use with Solenoid Point motors (PL10 / PL10E/ PL11) - The CDU is designed to store and release electrical power. When you switch your point blades (via switch like PL26 R/B/W/Y), the extra power ensures the blades throw properly every time. - The CDU requires a 16V Accessory out put either from your controller or via a separate accessory transformer (recommend Gaugemaster GMC WM1 Wall mounted transformer)