NCE Power Cab DCC Starter Set

NCE Power Cab DCC Starter Set An entire DCC system in the palm of your hand! This 2 Amp system can operate up to 4 OO sized locomotives or 8 N gauge trains. This cab provides all of the capability and ease of use that you’ve heard about in our Power Pro system, at an entry level price. Installation is a snap. Hook two wires to your track and plug in the cab. You’re off and running trains!   The Power Cab kit contains: NCE Power Cab 7' Power Cab Cable PCP Power Panel EU / UK Approved Power Supply Pro Cab Coiled Cord Manual.  

DCC Concepts Slim Vertical Mounted Magnetic Sensors (3-pack)

DCC Concepts - Slim Vertical Mounted Magnetic Sensors (3-pack) These detectors have been designed to be very easy to install. Super-slim at only 4mm in diameter, they will fit comfortably between the sleepers of DCCconcepts and Peco Code 100 and Code 75 track as well as most other brands of track in HO. (N scale users will need to temporarily move a sleeper while drilling, but will also find installation quite easy). They are Normally Off and are triggered or turned on by a small magnet that is attached to the loco or rolling stock. While it is always good to use smaller magnets and get the magnet as close as possible to any sensor such as this, we find that even with quite a small magnet we can get reliable results from up to 10mm away. Ideal for all detection and to trigger devices such as Cobalt Point Motors or Alpha. The connector is supplied so that the detectors can be used with our ADiA range of Accessory Decoders. Length of sensor: 15mm Width of sensor: 4mm Length of wire: 300mm Quantity in pack: 3 (Was DCP-TMS) Please note these are Normally Off or Normally Open momentary type connections

DCC Concepts Legacy Wired Joiners Code 100 Rail Pack of 6x Pairs

Legacy Wired Joiners Code 100 Rail Pack of 6x Pairs 300mm high quality track feed wires pre-soldered to Legacy Rail Joiners. Compatible with Code 100 track from Legacy and equivalent track from all major brands. Super-quick and easy to use – no soldering necessary! Pack contains 6 pairs - OO Scale

DCC Concepts Legacy Wired Rail Joiners Code 75 Track Pack of 6x Pairs

Legacy Wired Rail Joiners Code 75 Track Pack of 6x Pairs 300mm high quality track feed wires pre-soldered to Legacy Rail Joiners. Compatible with Code 75 track from Legacy and equivalent track from all major brands. Super-quick and easy to use – no soldering necessary! Pack contains 6 pairs - OO Scale

DCC Concepts LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack

DCC Concepts - LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack Wire-Free Baseboard connections Easily installed, super-accurate alignment dowels that remove the need for wires! PowerPoint dowels are a dream come true. Highly accurate, they can both transmit track power and perfectly align your baseboards. All of the electrial parts are gold plated too, so they'll never fail you! PowerPoints can confortably handle far more power than a DCC system can deliver, so you will only need to use one pair to reliably transfer power between average baseboards. Work carefully and you will obtain a great result when installing your new Legacy PowerPoint Dowels Clamp the baseboard ends together. Be sure the top surfaces are perfectly level and aligned. (You can temporarily screw an offcut of wood over the top of joint to ensure it is perfect) Mark the position for the dowels. Drill a pilot hole right through both ends using a 3mm drill. (keep it at 90 degrees to the board faces as this step will guide all subsequent drilling) Separate the two boards. Use a 19mm spade drill bit, and go just deep enough into the front face of each board end (2mm) (This is about right to allow the flange of the dowel to sit flush with the baseboard ends) Now, using a 13mm spade drill bit and working from the other side, drill right through the board. You will now have a 13mm hole with a 19mm flange. (Clean it up and remove anu rough edges and sawdust to make it ready for the Dowell installation) Add a little PVA to the grooves in each dowel & insert it flush with the face of the board. (If it’s too tight for a firm push-fit, ream the hole with sandpaper. Do NOT tap them in as you may damage them) To secure boards together after alignment, drill clearance holes for 1/4” bolts & wingnuts. (They do not need to be tight as the dowels will do all the work of aligning the boards perfectly) Connect the track power wires. Your PowerPoints are now installed and ready! By the way...PowerPoints will carry more than 5 amps of track power, so you will not overload them - ever!. Only top quality materials are used. The electrical parts are all gold plated so they will never tarnish and lose conductivity. PowerPoints can also be disassembled for cleaning or lubrication if needed, and we even supply you with spare parts in the pack. They really ARE designed to last forever!

Peco Tracklayers Tool set

Tracklayers Tool set A specially selected tool set from expert modellers here at PECO for laying track. These tools are vital to all modellers, included also is expert knowledge in the form a useful guide brought to you by the experts at Railway Modeller. Includes: Xuron track cutters Snipe nose pliers Snap-off knife with 10 spare blades Set of 4 needle files Pin vice Drill bits: 0.5 to 2.5 mm A4 cutting mat Sharpie marker pen Track pin pusher PECO track pins PECO rail cleaner Shows you how guide: 'Laying the track'

Hornby HM7070 - Power Bank

HM7070 - Power Bank Stay-alive for use with HM7000 decoders

DCC Concepts Cobalt iP Digital Point Motor (Single)

Cobalt iP Digital Point Motor (Single) - Any Scale Includes: - 1x Digital Point motor - Instruction manual  - Product Size:   - Width 28.5mm (67mm over the mounting wings)   - Depth 40mm (48mm over the mounting wings)   - Height 44mm (67mm over the connector) - Bag of attachments Features: The Cobalt-iP Digital’s super-low static current draw means very low power bus loading and the Cobalt-iP Digital is also able to cope with a very wide range of DC or DCC power supply voltages. We prefer 9~12V regulated power for DC, but any DCC voltage from 7 to 23 volts is acceptable. Cobalt-iP Digital is supplied with the throw bar already centred for easy installation. You can activate and de-activate self-centring and even swap the throw direction with a simple software command. This allows easy matching to layout needs, software driven computer displays, track diagrams or computer control. With Cobalt-IP “Intelligent Power” Digital Motors, you also have all the connection versatility you could ever need already built in. Frog power needs only one added wire, and a totally separate SPDT changeover switch can facilitate interlocking, control of signal feather indicators or ground signals, etc. Cobalt iP Digital also features the ability to add panel switches or control via DCC. The connection terminals used for panel switch connection are also able to give direct high/low state computer or DCC system feedback, so one motor really CAN do it all. Add to the above the ability to work with DC and super-simple wiring or DCC operation, or to combine digital and analog control… and Cobalt iP Digital really is the best choice for all layouts, no matter how you choose to power the trains!

Gaugemaster Black Wire (7 x 0.2mm) 100m

Black Wire (7 x 0.2mm) 100m This wire can be used for point motors, switches, track wiring and many other applications.

Gaugemaster Red/Black Twinned Wire (14 x 0.15mm) 10m

Red/Black Twinned Wire - Diameter (14 x 0.15mm) - Total length of cable is 10m - Ideal for track wiring needing two cables at a time.

Gaugemaster Twin Track Cased Controller

Twin Track Cased Controller Ideal for expanding the train set with the ability to control 2x locomotives independantly and power accessories - All in one controller with power lead wired - Sturdy Metal Casing - Accessory outputs ideal for point motors - Requires connecting to the mains via the socket - Suitable for N, OO and OO9 Gauges

Gaugemaster Single Track Walkabout Controller

Single Track Walkabout Controller Designed for those who wish to walk around there layouts or operate from afar - Designed to be wired with a Gaugemaster GM75 Plug and socket for panel mounting  - Can be powered via:  GMC-M1 Transformer, GMC-T1 Transformer, GMC-WM1 Transformer - Suitable for N,OO and OO9 Gauges

Gaugemaster COMBI Single Track Controller with Plug in Transformer

COMBI - Single Track Analogue Controller with Plug in Transformer Ideal for the beginner with a first train set or expanding on a current railway.  Includes - Hand held controller - Mains Transformer Technical: - Input: 230v Mains - Controlled Output: 12v DC - Accessory Output: 16v AC - Rating 1.1Amp - Suitable for N, OO, OO9 and (SMALL Dapol Locomotives) O Gauge

Peco Track Isolating Switch

Track Isolating Switch - Place between two sections of track to isolate one from the other - Used on Analogue railways to park up more than one locomotive on a section of track (like in engine sheds, station bay platforms)

Peco Rail Cleaner - abrasive rubber block

Rail Cleaner - The abrasive block is rubbed along the top surface of the rails to clean any dirt that will stop/disturb electrical connection of your model locomotives/ accessories (thus leading to poor operation) - IMPORTANT not to press too hard on the track (always better to take a few passes with the rubber than in one go) - Always be gently around point work whilst cleaning otherwise you could damage the point blades and tie-bar (switch mechanism) 

Peco Power Feed Joiners For C100 - C124 Rail (4 pairs)

Power Feeds - Designed for Code 100 OO Gauge track including (Setrack and Code 124 O Gauge Tracks) - 4 Pairs included

Peco Power Feed Joiners For C55 - C80 Rail (4 pairs)

Power Feeds - Designed for Code 55 and 80 N Gauge Tracks - 4 Pairs

Peco Power Feed Joiners For C70 - C75 - C83Rail (4 pairs)

Power Feeds - Designed for Code 75 OO Gauge Track (Including Code 70 and Code 83) - 4 Pairs