NCE Power Cab DCC Starter Set

NCE Power Cab DCC Starter Set An entire DCC system in the palm of your hand! This 2 Amp system can operate up to 4 OO sized locomotives or 8 N gauge trains. This cab provides all of the capability and ease of use that you’ve heard about in our Power Pro system, at an entry level price. Installation is a snap. Hook two wires to your track and plug in the cab. You’re off and running trains!   The Power Cab kit contains: NCE Power Cab 7' Power Cab Cable PCP Power Panel EU / UK Approved Power Supply Pro Cab Coiled Cord Manual.  

DCC Concepts Zen 3-Wire Medium Stay Alive for Zen Black & Blue+ Decoders

Zen 3-Wire Medium Stay Alive for Zen Black & Blue+ Decoders A single medium Stay-Alive with 3-wire connections to the decoder. Totally Plug and Play with Zen decoders. Usable with Zen Black, Zen Blue+, Lenz and ESU or any decoder with three-wire connections for Stay-Alive. Please note that connection of a DCCconcepts Zen Stay-Alive to a non-DCCconcepts decoder may invalidate your warranty, please check documentation which came with your decoder for details.

DCC Concepts Slim Vertical Mounted Magnetic Sensors (3-pack)

DCC Concepts - Slim Vertical Mounted Magnetic Sensors (3-pack) These detectors have been designed to be very easy to install. Super-slim at only 4mm in diameter, they will fit comfortably between the sleepers of DCCconcepts and Peco Code 100 and Code 75 track as well as most other brands of track in HO. (N scale users will need to temporarily move a sleeper while drilling, but will also find installation quite easy). They are Normally Off and are triggered or turned on by a small magnet that is attached to the loco or rolling stock. While it is always good to use smaller magnets and get the magnet as close as possible to any sensor such as this, we find that even with quite a small magnet we can get reliable results from up to 10mm away. Ideal for all detection and to trigger devices such as Cobalt Point Motors or Alpha. The connector is supplied so that the detectors can be used with our ADiA range of Accessory Decoders. Length of sensor: 15mm Width of sensor: 4mm Length of wire: 300mm Quantity in pack: 3 (Was DCP-TMS) Please note these are Normally Off or Normally Open momentary type connections

DCC Concepts Legacy Wired Joiners Code 100 Rail Pack of 6x Pairs

Legacy Wired Joiners Code 100 Rail Pack of 6x Pairs 300mm high quality track feed wires pre-soldered to Legacy Rail Joiners. Compatible with Code 100 track from Legacy and equivalent track from all major brands. Super-quick and easy to use – no soldering necessary! Pack contains 6 pairs - OO Scale

DCC Concepts Legacy Wired Rail Joiners Code 75 Track Pack of 6x Pairs

Legacy Wired Rail Joiners Code 75 Track Pack of 6x Pairs 300mm high quality track feed wires pre-soldered to Legacy Rail Joiners. Compatible with Code 75 track from Legacy and equivalent track from all major brands. Super-quick and easy to use – no soldering necessary! Pack contains 6 pairs - OO Scale

DCC Concepts LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack

DCC Concepts - LM-PP.4 Legacy Models Powerpoint Baseboard Dowels 4x pack Wire-Free Baseboard connections Easily installed, super-accurate alignment dowels that remove the need for wires! PowerPoint dowels are a dream come true. Highly accurate, they can both transmit track power and perfectly align your baseboards. All of the electrial parts are gold plated too, so they'll never fail you! PowerPoints can confortably handle far more power than a DCC system can deliver, so you will only need to use one pair to reliably transfer power between average baseboards. Work carefully and you will obtain a great result when installing your new Legacy PowerPoint Dowels Clamp the baseboard ends together. Be sure the top surfaces are perfectly level and aligned. (You can temporarily screw an offcut of wood over the top of joint to ensure it is perfect) Mark the position for the dowels. Drill a pilot hole right through both ends using a 3mm drill. (keep it at 90 degrees to the board faces as this step will guide all subsequent drilling) Separate the two boards. Use a 19mm spade drill bit, and go just deep enough into the front face of each board end (2mm) (This is about right to allow the flange of the dowel to sit flush with the baseboard ends) Now, using a 13mm spade drill bit and working from the other side, drill right through the board. You will now have a 13mm hole with a 19mm flange. (Clean it up and remove anu rough edges and sawdust to make it ready for the Dowell installation) Add a little PVA to the grooves in each dowel & insert it flush with the face of the board. (If it’s too tight for a firm push-fit, ream the hole with sandpaper. Do NOT tap them in as you may damage them) To secure boards together after alignment, drill clearance holes for 1/4” bolts & wingnuts. (They do not need to be tight as the dowels will do all the work of aligning the boards perfectly) Connect the track power wires. Your PowerPoints are now installed and ready! By the way...PowerPoints will carry more than 5 amps of track power, so you will not overload them - ever!. Only top quality materials are used. The electrical parts are all gold plated so they will never tarnish and lose conductivity. PowerPoints can also be disassembled for cleaning or lubrication if needed, and we even supply you with spare parts in the pack. They really ARE designed to last forever!

DCC Concepts Inter-Baseboard Connectors (2 Pack)

Inter-Baseboard Connectors (2 Pack) These clever pluggable screw-terminal connectors allow you to easily connect baseboard power with plug-and-socket connections! Suitable for DC or DCC on systems up to 5 Amps. Includes: - 2x Pluggable Screw-Terminal Connectors - Ferruled Connector Wire - Fixing Screws - Spare Ferrules (will require a crimping tool to use the spares)

DCC Concepts Cobalt Barrel-Plug Adapter (3 Pack)

Cobalt Barrel-Plug Adapter (3 Pack) Includes: A pack of three coaxial DC barrel plug adapters that will let you connect bare wires to a DC-plug fitted power supply that takes away the need to cut the plug off and get the soldering iron out. Suitable for the following DCCconcepts power supplies: - DCP-PS12 - DCP-12.3.XX - DCP-18.2.XX - DCP-18.5.XX

DCC Concepts AE Model 2-Wire High Power Plug & Play Stay-Alive (3-Pack)

AE Model 2-Wire High Power Plug & Play Stay-Alive (3-Pack) Compatible with Hornby TXS (HM7000) decoders (replaces R7377 / HM7070) to give improved performance and connectivity. AE Model 2-Wire Stay Alive for connection to AE Model Decoders including plug-and-play connector.   Dimensions  (individual) 23mm x 17mm x 6mm Cable length = 120mm  

DCC Concepts AE Model 2-Wire High Power Plug & Play Stay-Alive

AE Model 2-Wire High Power Plug & Play Stay-Alive Compatible with Hornby TXS (HM7000) decoders (replaces R7377 / HM7070) to give improved performance and connectivity. AE Model 2-Wire Stay Alive for connection to AE Model Decoders including plug-and-play connector. Dimensions 23mm x 17mm x 6mm Cable length = 120mm    

DCC Concepts Cobalt iP Digital Point Motor (Single)

Cobalt iP Digital Point Motor (Single) - Any Scale Includes: - 1x Digital Point motor - Instruction manual  - Product Size:   - Width 28.5mm (67mm over the mounting wings)   - Depth 40mm (48mm over the mounting wings)   - Height 44mm (67mm over the connector) - Bag of attachments Features: The Cobalt-iP Digital’s super-low static current draw means very low power bus loading and the Cobalt-iP Digital is also able to cope with a very wide range of DC or DCC power supply voltages. We prefer 9~12V regulated power for DC, but any DCC voltage from 7 to 23 volts is acceptable. Cobalt-iP Digital is supplied with the throw bar already centred for easy installation. You can activate and de-activate self-centring and even swap the throw direction with a simple software command. This allows easy matching to layout needs, software driven computer displays, track diagrams or computer control. With Cobalt-IP “Intelligent Power” Digital Motors, you also have all the connection versatility you could ever need already built in. Frog power needs only one added wire, and a totally separate SPDT changeover switch can facilitate interlocking, control of signal feather indicators or ground signals, etc. Cobalt iP Digital also features the ability to add panel switches or control via DCC. The connection terminals used for panel switch connection are also able to give direct high/low state computer or DCC system feedback, so one motor really CAN do it all. Add to the above the ability to work with DC and super-simple wiring or DCC operation, or to combine digital and analog control… and Cobalt iP Digital really is the best choice for all layouts, no matter how you choose to power the trains!

DCC Concepts 12-Way Pluggable Connectors (2 pairs)

12-Way Pluggable Connectors (2 pairs) Two pairs of 12 way pluggable connectors, suitable for heavy power connection between baseboards or perhaps the creation of an ‘easy disconnection’ structure between DCC systems and layout, these heavy duty tag strips are able to take a wide range of wires. They are a very strong connector that will last forever! Screws are brass and all pins/sockets are plated solid brass.

Gaugemaster Black Wire (7 x 0.2mm) 100m

Black Wire (7 x 0.2mm) 100m This wire can be used for point motors, switches, track wiring and many other applications.

DCC Concepts DCC Decoder Convertor 3 Wire to 2 Wire (3)

DCC Decoder Convertor 3 Wire to 2 Wire (3) - Pack of three solenoid decoders. - The SDC is a clever wee device that takes the outputs from a 3-wire accessory decoder and turns them into a 2-wire reversing DC decoder, allowing you to use most solenoid accessory decoders to power Kato, Cobalt or other brands of point motor. - Please note that for motor drive decoders you will also need to set ‘power on’ time for between 2 and 4 seconds.

Gaugemaster Red/Black Twinned Wire (14 x 0.15mm) 10m

Red/Black Twinned Wire - Diameter (14 x 0.15mm) - Total length of cable is 10m - Ideal for track wiring needing two cables at a time.

Gaugemaster White Wire (7 x 0.2mm) 10m

White Wire (7 x 0.2mm) 10m

Gaugemaster Yellow Wire (7 x 0.2mm) 10m

Yellow Wire (7 x 0.2mm) 10m

Gaugemaster Twin Track Cased Controller

Twin Track Cased Controller Ideal for expanding the train set with the ability to control 2x locomotives independantly and power accessories - All in one controller with power lead wired - Sturdy Metal Casing - Accessory outputs ideal for point motors - Requires connecting to the mains via the socket - Suitable for N, OO and OO9 Gauges

Gaugemaster Single Track Walkabout Controller

Single Track Walkabout Controller Designed for those who wish to walk around there layouts or operate from afar - Designed to be wired with a Gaugemaster GM75 Plug and socket for panel mounting  - Can be powered via:  GMC-M1 Transformer, GMC-T1 Transformer, GMC-WM1 Transformer - Suitable for N,OO and OO9 Gauges

Peco Turntable Motor

Turntable motor and control system  Ideal for anyone updating an older motor drive or converting a manual drive turntable into electric. This is a "NON Indexing" motor system meaning it has no pre set alignment programs, offering ultimate flexibility without any rewiring of your layout. Includes - Motor Unit and fixing Lugs - Hand Held Controller - Wire and fixings  - Manual of instructions - Requires power supply from a 12VDC 2Amp Supply NOT included - OO and N Scale Peco Turntables

Gaugemaster Red Wire (7 x 0.2mm) 10m

Red Wire (7 x 0.2mm) 10m

Peco PL1005 TwistLock Microswitch

PL1005 TwistLock Microswitch - Designed to be installed on a PL1000 Twistlock solenoid motor for use with Electrofrog Points - Wires can be either crimped on to the terminals or soldered  - Suitable for use with Electrofrog points

Peco PL38B Wire - Blue

PL38B Wire - Blue - 7 Metre Reel - 3 Amp Current Rating

Peco PL38BK Wire - Black

PL38BK Wire - Black - 7 Metre Reel - 3 Amp Current Rating

Peco PL38G Wire - Green

PL38G Wire - Green - 7 Metre Reel - 3 Amp Current Rating

Peco PL38R Wire - Red

PL-38R Wire - Red - 7 Metre Reel - 3 Amp Current Rating

Peco PL38Y Wire - Yellow

PL38Y Wire - Yellow - 7 Metre Reel - 3 Amp Current Rating

Gaugemaster Point Motor Wire Red/Green/Black Tripled (14 x 0.15) 10m

Point Motor Wire Red/Green/Black Tripled (14 x 0.15) 10m For use with Solenoid Point motors or SEEP Point motors

Gaugemaster Pink Wire (7 x 0.2mm) 10m

Pink Wire (7 x 0.2mm) 10m

Gaugemaster Green Wire (7 x 0.2mm) 10m

Green Wire (7 x 0.2mm) 10m

Gaugemaster Grey Wire (7 x 0.2mm) 10m

Grey Wire (7 x 0.2mm) 10m

Gaugemaster Black Wire (7 x 0.2mm) 10m

Black Wire (7 x 0.2mm) 10m

Gaugemaster Blue Wire (7 x 0.2mm) 10m

Blue Wire (7 x 0.2mm) 10m