Peco Turnout Switch Module Add-on

Turnout Switch Module (add on) - This module clips into either PL50 or other PL51 Switch Module units - Designed so you can expand your switching requirements to your chosen design. - Peco Electrics

Peco Twin Micro Switch Kit - for fitting to turnout motor PL10

Twin Micro Switch Kit  - for fitting to turnout motor PL10

Peco Smart Frog

Smart Frog unit - Designed to change Polarity on Electrofrog points whilst using the PLS100 SmartSwitch Set

Peco Track Isolating Switch

Track Isolating Switch - Place between two sections of track to isolate one from the other - Used on Analogue railways to park up more than one locomotive on a section of track (like in engine sheds, station bay platforms)

Peco Turnout Motor (Extended Pin)

PL10E Extended Pin Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases underneath the baseboard  - Pin might require cutting to length once installed (depending on baseboard thickness) - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales

Peco Turnout Motor

PL-10 Turnout Solenoid Point Motor (Switch Machine) - Designed to attach to PL9 Mounting bases or directly underneath a Peco point - Requires fixing and electrical supply (12v DC for an accessory output) - Suitable for OO and N Scales

Peco Side-mounted Motor

PL11 Side-mounted Motor - Designed to be placed alongside Peco Points to throw the point rails - Can be used with Electrofrog points but another type of switch will be required to change the polarity - OO Gauge

Peco Rail Cleaner - abrasive rubber block

Rail Cleaner - The abrasive block is rubbed along the top surface of the rails to clean any dirt that will stop/disturb electrical connection of your model locomotives/ accessories (thus leading to poor operation) - IMPORTANT not to press too hard on the track (always better to take a few passes with the rubber than in one go) - Always be gently around point work whilst cleaning otherwise you could damage the point blades and tie-bar (switch mechanism) 

Peco PL1005 TwistLock Microswitch

PL1005 TwistLock Microswitch - Designed to be installed on a PL1000 Twistlock solenoid motor for use with Electrofrog Points - Wires can be either crimped on to the terminals or soldered  - Suitable for use with Electrofrog points

Peco On-Off Switch (style matches PL26 series)

On-Off Switch (style matches PL26 series)

Peco On-On Changeover Switch (style matches PL26 series)

On-On Changeover Switch (style matches PL26 series)

Peco Passing Contact Switch - Black Lever

Passing Contact Switch - Black Lever

Peco Passing Contact Switch - Red Lever

Passing Contact Switch - Red Lever

Peco Passing Contact Switch - White Lever

Passing Contact Switch - White Lever

Peco Passing Contact Switch - Yellow Lever

Passing Contact Switch - Yellow Lever

Peco Four Pole Double Throw Toggle Switch (for use with SL-E383F)

Four Pole Double Throw Toggle Switch (for use with SL-E383F)

Peco Microswitch enclosed type

Microswitch enclosed type - Designed to fit into O Gauge points in the tie-bar housing  - The switch is designed to operate the polarity of electrofrog point work

Peco Microswitch Housing - (for SLE790BH)

Microswitch Housing - (for SLE790BH)

Peco Accessory Switch - for fitting to turnout motor PL10

Accessory Switch (mounts on top of PL10 and PL10E Point motors) - Designed to change the polarity of Electrofrog points - OO Gauge

Peco Capacitor Discharge Unit (CDU)

Capacitor Discharge Unit (CDU) - This device is for use with Solenoid Point motors (PL10 / PL10E/ PL11) - The CDU is designed to store and release electrical power. When you switch your point blades (via switch like PL26 R/B/W/Y), the extra power ensures the blades throw properly every time. - The CDU requires a 16V Accessory out put either from your controller or via a separate accessory transformer (recommend Gaugemaster GMC WM1 Wall mounted transformer)